UPVC Replacement Door Handles

Over time, the handles on your doors will wear out and will require replacement. When replacing them, it is crucial that the new handles conform to the dimensions of the aluminium window handle that was previously used.

The top screw's position the lever, and the keyhole size are the three measurements that you need to verify. Refer to the size guide for assistance in this.

Inline Lever/Lever

A lever/lever handle is a modern-day door handle designed to suit new or replacement double glazing handles doors. This type of door handle is available in a variety of designs and finishes. A number of manufacturers make this handle, including Avocet ERA, Fullex, Hoppe, Mila, Millenco & Yale.

Fab and Fix Windsor Inline Sprung Lever Door Handle

The handles made of uPVC/Composite are made from durable materials, and are ideal for doors with multiple points that require a strong design. The handles are inline and run with the same spindle as well as screw fixings, so they can be easily fitted to existing or new replace upvc door handle/Composite doors.

The design of the sprung lever allows the window handle repairs to be set and angled for comfortable operation and is suitable for all users. The handle has been tested to 200,000 cycles. This ensures that the quality of finish and performance over time. The lever that is sprung can be reduced to accommodate a wider range of locks. This is useful for narrower doors where the cylinder is situated further back from the door. A lever that is shorter can be used for doors with a latch which can be operated with the thumb on the inside.

Lever Pad

A Lever Pad door handle made of upvc operates differently than lever handles on doors. These handles can operate from a single spindle (inline) or independently from each side by using two offset spindles or inline (pad). They are generally employed on UPVC double glazed doors and come in many variations & finishes.

The handles have been tested to the minimum of 200,000 cycles and are available in various finishes including White Silver, Chrome, & Gold. The finish is in line with BS EN 1670:2007 Grade 5 and is also resistant to corrosion, which gives the handle a high degree of durability and performance for its intended use.

All UPVC levers for handles come with a spindle, screws and can be mounted on a uPVC door. The backplate fixing centres of 211mm allow for a wider handle, which can often be a benefit when replacing a faulty or worn multi point door lock mechanism. The handle levers are spring-loaded, which solves the issue of handles that slide out of the horizontal position when not in use.

It is crucial to match the dimensions of the PZ for both the multipoint lock as well as the uPVC doors when selecting a replacement UPVC spindle and handle. This measurement is often called the 'handle centre' or 'cylinder centres and is an essential aspect to match the appropriate handles.

After you have determined the proper PZ size it is important to ensure that the lever and push pads are designed to match the American with Disabilities Act compliant handles you require for your door. These are typically of a round or square shape with an internal lever as well as an external push pad.

The majority of UPVC Lever Pads we sell are spring-loaded. This means they can be reverted to a horizontal state when not in use instead of hanging and possibly sticking in the frame. This keeps draughts out of the home. It is also the case that the majority of the UPVC handle lever pad style changing window handles are swivel, allowing you to install them on either side of the door.

Euro Cylinder

Cylinder locks are found on uPVC and other kinds of doors. They operate with a key to unlock a cylinder case that is then revealed with pins that can be aligned to those in the lock body, allowing them to turn an revolving cam, opening the door. Euro cylinders can be fitted with up to six pins with both internal and external doors typically needing different levels of security.

The selection of a cylinder is vital. It depends on the use that your doors and handles receive. Doors that are external, for instance should be equipped with cylinders with greater security, whereas internal doors can be secured with a standard cylinder. Additionally, certain cylinders come with additional features that increase security further, such as anti-drill or anti-bump features.

To make sure that the euro cylinder is the correct size for your door, it must be measured correctly. The cylinder needs to be measured from the screw hole in the center to the ends of the cylinder. This includes the thumb turn in the event that one is present. It is best to do this while the lock is in place however in the event that this is not possible, you can remove it to take measurements. It is crucial to not have a extension of the cylinder beyond the handle or escutcheon. This can make it vulnerable to snapping lock attacks.

The design of the latest cylinders includes anti-drilling and bump resistance features. These are designed to reduce the chance of attack by forcing cylinders to turn in a different direction. This can help deflect the attack, and protect your door.

There are cylinders that have been constructed to withstand snapping. This is a more frequent type of attack on cylinders where the break line in the lock is smashed using a special tool to snap off the front of the cylinder and allow the door to open. This is faster and less difficult than opening multipoint locks and leaves little evidence of a break-in, which can impede an insurance claim.

Spring Cassette

This spring cassette is located in the base plate of the door handle. It is a spring-loaded solution to return your multipoint lock handles back to their original position after usage. These handles used to have no spring and would droop when the locking mechanism was removed. This simple part is the most effective way to fix this problem. It also stops your upvc door from becoming stuck in the closed or open position since they are difficult to close manually.

These spring cassettes were created to be used with a sprung multipoint lock. They are not compatible with handles that aren't sprung, and you will have to cut a hole into the backplate to allow them to fit. (Please see the image for a technical diagram). They are a replacement for existing damaged or missing cassettes inside the door handle backplate of numerous brands of uPVC doors. They are available as a single unit. They come with a square cut out that is able to accommodate an 8mm shaft.

These spring cassettes provide an excellent value solution for the problem of door handles that are sagging. They are simple to install and can extend the life of your uPVC door. Contact us to learn more about our wide range of uPVC accessories and spares. We are always available to offer professional advice and assistance you.